45 Degree Copper Stamping with Loctite coating

Locking tabs clip seal securely on fitting

Conical rings for multiple points of contact

Used to prevent leaks that are caused by galling, vibration, pulsation and extreme temp changes

A perfect solution for a leak free connection in todays harshest environments

Permits free condensate flow while blocking odors, noise and insects

Freeze resistant

Mini waterless in-line trap sized for use in ductless mini-split applications

The equipment rails shall be 18 gauge galvanized steel, monolithic construction, with integral base plate

Continuous welded corner seams, factory installed 2 x 4 wood nailer and including an 18 gauge galvanized counter-flashing complete with screws

On Built-Up or Modified Bitumen Roofing, Concrete or Wood Decks without insulation use style ER-3A with built-in cant extended to full mitered corners with a height of 8" overall

Ideal for Ductless Mini-Split

Flexible Ivory

Corrugated non-kink

The Deck-Mate flashing incorporates a stepped profile which creates a compression seal between the schedule 40 piping and the flashing

Designed with proper reinforcing ribs to allow the flashing to maintain rigidity and the shape of the product

By combining the stepped profile and the reinforcing ribs the product will properly accommodate the use of a stainless steel clamp The clamp is crucial in maintaining a water tight seal for years to come

All other products on the market incorporate the use of caulk to seal the penetration

The National Roofing Contractor Association states, in their better roofing practices, that caulk should never be used as a primary sealer of a penetration

The Deck-Mates are designed to accommodate projections from .125"-26" in diameter and work in conjunction with any configuration of corrugated metal roof

The product is engineered to incorporate a dead soft aluminum flange that bends to any contour, roof irregularity or pitch

Deck-mate is available in two styles the standard for normal penetration and Retrofit for piping that can not be disconnected

Flashings are also available in two materials, standard EPDM and high temperature Silicone

Furnish and install a tall points where 26" or less pipes penetrate the metal roof and wall system

The Deck-Mate shall be EPDMor Silicone (high temperature) compression molded rubber

Material shall have a serviceable temperature range of -60 F to 270 F for EPDM and -100 F to 500 F for Silicone Both products will be resistant to ozone and ultraviolet

Unit shall have 1" wide corrosion resistant flexible aluminum base The Deck-Mate shall also include Portals Plus' Snaplock Clamp (except DM0)

The Deck-Mate flashing incorporates a stepped profile which creates a compression seal between the schedule 40 piping and the flashing

Designed with proper reinforcing ribs to allow the flashing to maintain rigidity and the shape of the product

By combining the stepped profile and the reinforcing ribs the product will properly accommodate the use of a stainless steel clamp The clamp is crucial in maintaining a water tight seal for years to come

All other products on the market incorporate the use of caulk to seal the penetration

The National Roofing Contractor Association states, in their better roofing practices, that caulk should never be used as a primary sealer of a penetration

The Deck-Mates are designed to accommodate projections from .125"-26" in diameter and work in conjunction with any configuration of corrugated metal roof

The product is engineered to incorporate a dead soft aluminum flange that bends to any contour, roof irregularity or pitch

Deck-mate is available in two styles the standard for normal penetration and Retrofit for piping that can not be disconnected

Flashings are also available in two materials, standard EPDM and high temperature Silicone

Furnish and install a tall points where 26" or less pipes penetrate the metal roof and wall system

The Deck-Mate shall be EPDMor Silicone (high temperature) compression molded rubber

Material shall have a serviceable temperature range of -60 F to 270 F for EPDM and -100 F to 500 F for Silicone Both products will be resistant to ozone and ultraviolet

Unit shall have 1" wide corrosion resistant flexible aluminum base The Deck-Mate shall also include Portals Plus' Snaplock Clamp (except DM0)