The Deck-Mate flashing incorporates a stepped profile which creates a compression seal between the schedule 40 piping and the flashing

Designed with proper reinforcing ribs to allow the flashing to maintain rigidity and the shape of the product

By combining the stepped profile and the reinforcing ribs the product will properly accommodate the use of a stainless steel clamp The clamp is crucial in maintaining a water tight seal for years to come

All other products on the market incorporate the use of caulk to seal the penetration

The National Roofing Contractor Association states, in their better roofing practices, that caulk should never be used as a primary sealer of a penetration

The Deck-Mates are designed to accommodate projections from .125"-26" in diameter and work in conjunction with any configuration of corrugated metal roof

The product is engineered to incorporate a dead soft aluminum flange that bends to any contour, roof irregularity or pitch

Deck-mate is available in two styles the standard for normal penetration and Retrofit for piping that can not be disconnected

Flashings are also available in two materials, standard EPDM and high temperature Silicone

Furnish and install a tall points where 26" or less pipes penetrate the metal roof and wall system

The Deck-Mate shall be EPDMor Silicone (high temperature) compression molded rubber

Material shall have a serviceable temperature range of -60 F to 270 F for EPDM and -100 F to 500 F for Silicone Both products will be resistant to ozone and ultraviolet

Unit shall have 1" wide corrosion resistant flexible aluminum base The Deck-Mate shall also include Portals Plus' Snaplock Clamp (except DM0)

The Deck-Mate flashing incorporates a stepped profile which creates a compression seal between the schedule 40 piping and the flashing

Designed with proper reinforcing ribs to allow the flashing to maintain rigidity and the shape of the product

By combining the stepped profile and the reinforcing ribs the product will properly accommodate the use of a stainless steel clamp The clamp is crucial in maintaining a water tight seal for years to come

All other products on the market incorporate the use of caulk to seal the penetration

The National Roofing Contractor Association states, in their better roofing practices, that caulk should never be used as a primary sealer of a penetration

The Deck-Mates are designed to accommodate projections from .125"-26" in diameter and work in conjunction with any configuration of corrugated metal roof

The product is engineered to incorporate a dead soft aluminum flange that bends to any contour, roof irregularity or pitch

Deck-mate is available in two styles the standard for normal penetration and Retrofit for piping that can not be disconnected

Flashings are also available in two materials, standard EPDM and high temperature Silicone

Furnish and install a tall points where 26" or less pipes penetrate the metal roof and wall system

The Deck-Mate shall be EPDMor Silicone (high temperature) compression molded rubber

Material shall have a serviceable temperature range of -60 F to 270 F for EPDM and -100 F to 500 F for Silicone Both products will be resistant to ozone and ultraviolet

Unit shall have 1" wide corrosion resistant flexible aluminum base The Deck-Mate shall also include Portals Plus' Snaplock Clamp (except DM0)

Furnish and install the Portals Plus Medium Pipe Boot at all points where any projection penetrates the roof system and is less than 6 Inch in diameter

The Medium Pipe Boot shall include 60 mil EPDM or NEOPRENE compression molded body and shall include 70 mil PVC (Polyvinyl Chlo-ride) or TPO (Thermoplastic Olefin) injection molded body

The Medium Pipe Boot shall also include Portals Plus Snaplock Clamp

Whenever necessary utilize Portals Plus Adapters to seal to square tubing and angle iron and for round penetrations less than 1 Inch in diameter

Use white or black as necessary

Attachment of Medium Pipe Boot to roof system shall be done in accordance with Portals Plus Installation Instructions and the roofing membrane manufacturers requirements

Furnish and install Portals Plus Galvanized Shingle Flashings as manufactured by Portals Plus, Inc. at all round penetrations from 1.25" through 4", occurring in shingle roofing systems under 40 Degree slope or as shown on drawings

The Shingle Flashings shall consist of an elastomeric collar integrally locked into a rigid base of 24 gauge galvanized steel

The elastomeric collar shall be resistant to ozone, ultraviolet degradation and temperature extremes

The base shall be rust resistant

Furnish and install Portals Plus Galvanized Shingle Flashings as manufactured by Portals Plus, Inc. at all round penetrations from 1.25" through 4", occurring in shingle roofing systems under 40 Degree slope or as shown on drawings

The Shingle Flashings shall consist of an elastomeric collar integrally locked into a rigid base of 24 gauge galvanized steel

The elastomeric collar shall be resistant to ozone, ultraviolet degradation and temperature extremes

The base shall be rust resistant

Furnish and install Portals Plus Galvanized Shingle Flashings as manufactured by Portals Plus, Inc. at all round penetrations from 1.25" through 4", occurring in shingle roofing systems under 40 Degree slope or as shown on drawings

The Shingle Flashings shall consist of an elastomeric collar integrally locked into a rigid base of 24 gauge galvanized steel

The elastomeric collar shall be resistant to ozone, ultraviolet degradation and temperature extremes

The base shall be rust resistant